Universe Sandbox

General Category => Astronomy & Science => Topic started by: blotz on November 17, 2013, 05:47:34 AM

Title: 3D Printing
Post by: blotz on November 17, 2013, 05:47:34 AM
fyi there's the octave enclosure for 180 (http://www.amazon.com/Octave-3D-Printer-Enclosure/dp/B00EK4VXNU)
So i was wondering about this

If i wanted to print a "T"
the 3d printer would print the straight up part first. That i understand because it's just going up. but when it gets to the top part, and it's a vertical line, how does the printer print over open space? does it just like hold the plastic over it until it dries off and then keeps printing or something?
Title: Re: 3D Printing
Post by: Bla on November 17, 2013, 10:39:30 PM
You could print a T if you put it like when you write it on paper without it having to print over open space, so the side you read from faces up/down. But I don't know how it would print over open space.
Title: Re: 3D Printing
Post by: atomic7732 on November 18, 2013, 12:09:18 PM
really carefully and with gravity turned off
Title: Re: 3D Printing
Post by: Darvince on November 18, 2013, 12:13:26 PM
Wouldn't it actually just have "printers" over both the top and sides?
Title: Re: 3D Printing
Post by: blotz on November 18, 2013, 01:06:32 PM
well the "T" was just an example, i saw printers printing over emtpy space
really want to buy one  to try it out, but already spend it on my new comptuer, in about 2 weeks
my best bet is that they let it dry enough and then move on
Title: Re: 3D Printing
Post by: Camacha on December 18, 2013, 03:02:52 PM
Actually, there are a number of 3D-printing technologies, some of which can print across spaces and some of which can not. Each technology has certain advantages and drawbacks.

The most common technology you see nowadays is FDM, which is basically an automated glue gun. This technology is usually not capable of crossing gaps (small gaps and some very specific situations excepted). It is capable of some overhang, but you have to be careful with that, otherwise you will see sagging or even collapses. In professional printers sometimes two materials are used, one of which is dissolvable. The dissolvable material is used for printing supports, on which the non dissolvable material can be printed. Afterwards the dissolvable material is removed by dissolving it, leaving only the desired bits. Note that entry level printers can rarely do this and that objects are typically designed to work around this limitation. Advantages are that the technology is cheap in both machine and material costs and that it is capable of printing hollow objects. Printed products also have good mechanical qualities. A disadvantage is that the resultion is typically low, or it becomes a really slow process (these are inversely related to each other).

Another popular technology is SLS, which is a laser sintering powder together. It does this for one layer, then the machine deposits another layer across the print bed and then sinters parts of the new layer onto the previous one. You understand that this means that parts are supported by the powder while printing. This means it is not restricted by gravity. At the end of the print process, the powder is cleared out and usually recycled. Advantages of this technology are that it is moderately cheap, has a good resolution and produces nice, strong and clean products. Disadvantages are that models can not be hollow without an opening to the outside world (the powder can not get out) and that the plastic can be a bit brittle (not food safe and absorbs substances).

A third technology is SLA, which uses projected or laser light and a light sensitive resin. By directing a couple of intersecting beams to a certain spot, the plastic on this spot is cured and hardened, leaving the rest a fluid. For overhangs usually temporary supports are used. Advantages are really high resolutions, making for really smooth and detailed objects. Disadvantages are that the price of the curing resin is typically high and that it has limited mechanical qualities. Hollow objects are also only possible with openings to the outside world, as the fluid needs to be removed (and is expensive).

There are more technologies, but these are the most common ones. Please read about them on the Wikipedia page (http://en.wikipedia.org/wiki/3D_printing#Additive_processes (http://en.wikipedia.org/wiki/3D_printing#Additive_processes)). 3D-printing is one of my pet subjects and I have worked with or seen quite a number of these technologies (LOM, PP, SLA, SLS, FDM, DMLS and silver through FDM and lost wax) so if you have any additional questions, ask away!